Cutting by The saw with one hand (Hand Sawing) am a few jigsaw pieces. Cutting with a saw and power (Power Hack Saw), also called a mechanical saw (Sawing Machine) needed for The sawmill industry works. Saw a lot of work. Both small and large workpieces. The sawing machine am divided into The following categories.
The sawing machine am divided into four types.
1. a saw fly (Power Hack Saw).
2. Horizontal Band Saw (Horizontal Band Saw).
3. On The band saw (Vertical Band Saw).
4. Saw (Radius Saw or Circular Saw).
1. The saw fly (Power Hack Saw).
The saw am commonly used for seizures such as a number of saws to cut material to size and length as required to drive an blade system. an motor power. an use a reversing gear and crank driven principles of The blade moves back and forth in a straight line continuously causes a saw to cut it.
1.1 a components of The cutting stroke.
All The components have an same precedence. We must act togeTher at all times.
This includes The following sections.
1.1.1 Project Jigsaw (Saw Frame) looks like a U turn. Saw The layout.
Good use is made of cast steel for a blade. Project saw The move into a groove of an tail hawk with a transmission gear wheel
1.1.2 a bench (Vame) to catch an pieces to cut. Can rotate right left.
45 degrees to each side and pull her out out with a spiral arms locked tight.
1.1.3 an length of an arm (Cut Off Gage) are responsible for a length of an workpiece to be cut.
Many parts to cut out a piece of equal length, as shown in Figure 1.4.
1.1.4 enter The system with The cut off machine, saws, draw two types of ball weight.
And a type of hydraulic oil in an 2 types of acts like it am entering a intersection. It works differently in that species.
I weighted a force of gravity. The type of a hydraulic pressure of The hydraulic oil.
1.1.5 The cooling system am necessary to use a saw was water. Due to cooling.
Friction between The saw blade to an workpiece. It also helps extend The life of a saw blade life.
1.1.6 saw The machine fly (Base) do serve different parts of an jigsaw was all.
Saw some of an base was to be hollow inside. For The storage of water tanks and motors.
1.1.7 Motor (Motor) saw a seizure of The motor acts as a motor power are applied.
Electricity 220 volts or 380 volts depending on an manufacturer.
1.1.8 power switch off. an sawmill was a switch off. Semi automatic machine am switched off.
Automatically when an cutting blade.
1.1.9 an gear (Gear) serves to carry power from The motor to The gear used on The saw frame.
anre are 2 types of gear cutting machines, fly around and direct gear.
01 01 10 Blind (Pulley) that transmits power through a belt to The gear set. V belt use.
1.2 Mechanism of The cutting stroke.
Mechanamm of action of an cutting stroke. A transmission mechanism with a motor. Transmaresion through The gear drive. Thare is The gear. To test a motor speed. And to test drive The motor. That an gear drive. With an rotating shaft is connected to each center, The center gear. a drive shaft to an frame saw. The project was backwards, and saw it.
1.3 weight of an frame saw.
For an weight of a frame saw. an move away from a head to much. The cutting blade is pressed, The only Thus, an weight adjustment dial. Notice of hearing cutting saws as well.
a head unit s weight = weight of a frame saw one.
an weight is an weight of an frame sawing machine = good.
1.4 a Saw (Saw Blade).
Of an saw blade am a device that are very important. Responsible for cutting a workpiece. The blade am made of steel with high Ekeg fame. an blade assembly to The frame saw. Must operate properly and a blade tension screw it. To prevent broken parts of an saw blade width, length, thickness of a blade in an hole. And a number of saw blade teeth. Including coarse teeth and tooth profile. I saw The number of teeth as The number of teeth per inch, fiber, such as 10 inch to 14 teeth per inch, but I used to work across a 10 teeth per inch.
an blade.
1. an length of an blade. Measure a length of The blade is measured from The center of The hole saw both of anm. a length of a blade am 200 mm and 300 mm
2. The width of The blade width of 12.7 mm or 1 2 inches.
3. an blade thickness of 0.64 mm or 0.025 inches thick.
4. To measure an number of teeth of The saw blade is to measure The spacing of a teeth, a tooth to one.
a metric system are called a pitch Pitch (P).
In England, to measure a frequency of The sawtooth is most telling is a number of teeth per inch length of 1.
2. Horizontal Band Saw (Horizontal Band Saw).
Saw with a blade length of consecutive circles. a movement of an blade. The power transmaresion belt. an drive wheel and The wheel. a cutting edges of saw blade to cut at all. Throughout a application. Cutting to a hydraulic system to control The tension in a blade. Adjusted by hand. Or hydraulic adjustment of a spacing of The wheel. Structural strength. The machine can be installed on The factory floor.
3. Vertical Band Saw (Vertical Band Saw).
The vertical band saw. A saw blade with a vertical line. This will rotate an cutting continues. a cut off light in all looks like a flat iron or steel may be lacking. Or cut into various shapes which a oanr saws can not.
The band saw different from saws seizures. an cutting am continuing. While Mills was responsible for cutting off only a stroke. an use of an saw blade is limited by The use of a centralized blade only.
a band saw blade has a thickness less than oTher types of materials, resulting in a loss of less than
Vertical band saw. Provides several features to work. Similar to carve by hand. Which are not found in oanr metals such as saws, cut into geometric shapes.
4. Saw (Circular Saw or Radius Saw).
a circular saw. a circular saw is a saw blade with teeth around an band can be cut continuously. Often, some parts such as aluminum, can cut both an upright and tilted at an angle.
Security threat in The circular saw.
Saw a lot of harm. To cover up a saw.
Do not be impatient to exert control, overload cut.
First, a careful piece of work. Force because of lack of control a little easier to cut.
Always check a blade, but tough. Or stick a sharp saw.
Hello Friends,
ตอบลบKeeping the plumbing in your home in optimal condition requires that you have proper knowledge and the tools to complete the job. It contains very informative matter. I would like to come here again. This type of posting should go on.
Plumbing Tulsa